HDPE
High density Polyethylene (HDPE): is a highly crystalline non-polar thermoplastic resin produced through the copolymerization of ethylene and a small amount of ¦Á-olefin monomer. HDPE is synthesized under low pressure and is therefore also called low-pressure polyethylene. HDPE is mainly a linear molecular structure and has little branching. It has a high degree of crystallization and high density. It can withstand high temperatures and has good rigidity and mechanical strength and anti-chemical corrosion
.
|
Performance of the project
|
Test condition [condition]
|
The test method
|
The test data
|
The data unit
|
|
|
Density mass index
|
|
GB/T 1033
|
0.948¡À0.002
|
g/cm3
|
|
Density test results
|
|
GB/T 1033
|
0.948
|
g/cm4
|
|
Melt flow rate mass index
|
190ºC/5.0kg
|
GB/T 3682
|
0.23¡À0.03
|
g/10min
|
|
Melt flow rate test results
|
|
GB/T 3682
|
0.25
|
g/10min
|
|
Melt flow rate mass index
|
190ºC/21.6kg
|
GB/T 3682
|
6.2¡À1.5
|
g/10min
|
|
Melt flow rate test results
|
|
GB/T 3682
|
6.4
|
g/10min
|
|
Mechanical properties of
|
Tensile yield strength quality index
|
|
GB/T 1040
|
¡Ý23
|
MPa
|
|
Test results of tensile yield strength
|
|
GB/T 1040
|
27.6
|
MPa
|
|
Elongation at break quality index
|
|
GB/T 1040
|
¡Ý600
|
%
|
|
Test results of elongation at break
|
|
GB/T 1040
|
804
|
%
|
|
Quality index of impact strength of simply supported beam
|
|
GB/T 1043
|
¡Ý25
|
KJ/m2
|
|
Test results of impact strength of simply supported beam
|
|
GB/T 1043
|
26.7
|
KJ/m2
|
|
Other properties
|
Volatile matter quality index
|
|
GB/T 15658 1
|
¡Ü350
|
mg/kg
|
|
Volatile test results
|
|
GB/T 15658 1
|
Did not check out
|
mg/kg
|
|
Biochemical property
|
Cleanliness (color granule) quality index
|
|
SH/T 1541
|
¡Ü20
|
grain/kg
|
|
Cleanliness (color particle) test results
|
|
SH/T 1541
|
0
|
grain/kg
|
|
Cleanliness (impurities) quality index
|
|
SH/T 1541
|
¡Ü60
|
grain/kg
|
|
Cleanliness (impurities) test results
|
|
SH/T 1541
|
0
|
grain/kg
|
1.Fiber ( Carpet, Textils, Upholstery, etc.)
2.Film ( shopping bags, casting film, multilayer film, etc.)
3.Blow Molding ( Medical & Cosmetic container, Lubricant & Paint container, etc)
4.Extrusion Molding ( Sheet, Pipe, Wire & Cable, etc.)
5.Injection Molding ( Automotive, Electronic, Construction, House wares, Furniture,
Toys, etc.)
25kg/ carton or 25kg/bag, or per your requirement
25kgs net weight in PP woven or PE plastic bag about 20 tons for 20" container
